The SM Nivel V3 or “Semovar” is the first APV of its kind. Its modular design makes it extremely versatile and customizable to individual needs. Instead of a 510 connection, the Kayfun V3 and V3.1 can be mounted via hybrid connection using the hybrid collectors tank, thus the atomizer and the APV fuse into one compact unit. The chip unit contains the heart of the APV: The SM Nivel V3 chip. The customizability continues within this chip, as it contains functions as choosing between variable wattage and variable voltage, setting the display brightness as well as choosing whether the button, the display or both shall be illuminated during usage. All settings are saved and restore automatically after battery exchange. The chip itself provides a broadband from 3-6 Volts or 5-15 Watts, a maximum amperage of 3-3,5 Ampere and a non-pulsed direct-current voltage. Therefore it is able to fire atomizers down to one Ohm.
For those who are still not satisfied, the Semovar can also convert into a pure mechanical mod. Just remove the chip unit and exchange the bottom cap with a bottom switch.
Technical features Direct-current voltage (not pulsed)
Atomizers down to one Ohm can be used
Versatile and customizable through modular design
510 connections with adjustable plus terminal
Galvanized connections for better conductivity
Hybrid connection for Kayfun V3/ V3.1 possible (accessory needed)
Completely demountable, thus easy to maintain
Bottom cap adjustable for better conductivity
Cache saves user settings through exchanging the battery
Vapetime counter (experienced user may be able to diagnose batteries with it)
Technical data Broadband voltage: 3.0 Volt – 6.0 Volt.
Maximum power: 15 Watts.
Lowest working resistance: 1.0 Ohm.
Maximum amperage: 3.0A – 3.5A
Display: bipartite seven-segment display and illuminated switch via LED. Reverse battery protection with additional LED
Controls: button.
Variable voltage mod, 0.1V steps
Variable wattage mode, 0.2W steps from 3-10W, 0.5W steps from 10-15W
Sleep mode: On/Off via 3 fast clicks on the switch.
Shows battery charge with and without firing in the menu.
Battery status can be displayed while usage.
Brightness of display illumination adjustable in 5 shades.
Ohmmeter
Time limit for firing: 15s, the device will shut down into standby mode after pressing the button for 30s.
Protection against overheating: Error is shown, when the ship hit a temperature over 60°C.
Short circuit protection
Reverse battery protection
Attention! Due to the production process, the components of the SM Nivel V3 beta and gamma version are finished separately and, depending on lighting, slight differences in the shade of individual parts may or may not be apparent when assembled.
Dimensions diameter: 22mm
length
|
Without atomizer (with 510 connector)
|
With Kayfun Lite (equals Kayfun V3/ V3.1 in hybrid mode)
|
With Kayfun 3.1 and 510 connection
|
18350
|
10,1cm
|
15,6cm
|
16,4cm
|
18500
|
11,6cm
|
17,1cm
|
17,9cm
|
18650
|
13,1cm
|
18,6cm
|
19,4cm
|
Warranty: 1 year, excluded are insulators.
Using the menu To access the menus and change settings, you will press the button the indicated number of times and wait a second while the screen changes from the initial display to an adjustable display. At the adjustable display, you are able to edit the settings to customize your vape for you.
When an atomizer is attached 3 presses- “ON” - Will turn on
4 presses- “dn” - Set your voltage/wattage down.
5 presses- “UP” - Set your voltage/wattage up.
6 presses- “rA” - Check the resistance of your atomizer.
7 presses- “Ub” - Display remaining battery life in volts (4.2v fully charged, 3.2v dead). Can also be used to check your voltage under load.
When an atomizer is not attached 6 presses- “SP” - Set power. You are able to increase the wattage at .2w increments, and .5w increments from 10w - 15w (Will display as “10” if at 10w, or “10.” if at 10.5w)
7 presses- “SU” - Set voltage. Increases voltage in increments of .1v.
8 presses- “rA” - Check the resistance of your atomizer.
9 presses- “Ub” - Display remaining battery life in volts (4.2v fully charged, 3.2v dead). Can also be used to check your voltage under load.
10 presses- “Sd” - Set display. You can change the intensity of the LED.
11 presses- “SL” - Set LED. Here you can change which LED (Button or display, both, or none) will light up when vaping.
12 presses- “H “ - Vape timer / vape timer reset. First screen is hours, second screen is minutes. If you push the button a second time, you will see “CL”. This will reset the counter if you press the button again.
13 presses- “Fr” - Firmware version. This will show which firmware is currently installed in the device.